LIN mode functions. More...

Functions
void	USART_LINBreakDetectLengthConfig (USART_TypeDef *USARTx, uint16_t USART_LINBreakDetectLength)
	Sets the USART LIN Break detection length. More...

void	USART_LINCmd (USART_TypeDef *USARTx, FunctionalState NewState)
	Enables or disables the USART's LIN mode. More...

void	USART_SendBreak (USART_TypeDef *USARTx)
	Transmits break characters. More...

Detailed Description

LIN mode functions.

 ===============================================================================
                                LIN mode functions
 ===============================================================================  

  This subsection provides a set of functions allowing to manage the USART LIN 
  Mode communication.
  
  In LIN mode, 8-bit data format with 1 stop bit is required in accordance with 
  the LIN standard.

  Only this LIN Feature is supported by the USART IP:
    - LIN Master Synchronous Break send capability and LIN slave break detection
      capability :  13-bit break generation and 10/11 bit break detection


  USART LIN Master transmitter communication is possible through the following procedure:
     1. Program the Baud rate, Word length = 8bits, Stop bits = 1bit, Parity, 
        Mode transmitter or Mode receiver and hardware flow control values using 
        the USART_Init() function.
     2. Enable the USART using the USART_Cmd() function.
     3. Enable the LIN mode using the USART_LINCmd() function.
     4. Send the break character using USART_SendBreak() function.

  USART LIN Master receiver communication is possible through the following procedure:
     1. Program the Baud rate, Word length = 8bits, Stop bits = 1bit, Parity, 
        Mode transmitter or Mode receiver and hardware flow control values using 
        the USART_Init() function.
     2. Enable the USART using the USART_Cmd() function.
     3. Configures the break detection length using the USART_LINBreakDetectLengthConfig()
        function.
     4. Enable the LIN mode using the USART_LINCmd() function.


@note In LIN mode, the following bits must be kept cleared:
        - CLKEN in the USART_CR2 register,
        - STOP[1:0], SCEN, HDSEL and IREN in the USART_CR3 register.

Function Documentation

void USART_LINBreakDetectLengthConfig	(	USART_TypeDef *	USARTx,
		uint16_t	USART_LINBreakDetectLength
	)

Sets the USART LIN Break detection length.

Parameters

USARTx,:	where x can be 1, 2, 3, 4, 5 or 6 to select the USART or UART peripheral.
USART_LINBreakDetectLength,:	specifies the LIN break detection length. This parameter can be one of the following values: USART_LINBreakDetectLength_10b: 10-bit break detection USART_LINBreakDetectLength_11b: 11-bit break detection

Return values

None

void USART_LINCmd	(	USART_TypeDef *	USARTx,
		FunctionalState	NewState
	)

Enables or disables the USART's LIN mode.

Parameters

USARTx,:	where x can be 1, 2, 3, 4, 5 or 6 to select the USART or UART peripheral.
NewState,:	new state of the USART LIN mode. This parameter can be: ENABLE or DISABLE.

Return values

None

void USART_SendBreak ( USART_TypeDef * USARTx )

Transmits break characters.

Parameters

USARTx,: where x can be 1, 2, 3, 4, 5 or 6 to select the USART or UART peripheral.

Return values

None

Functions

Detailed Description

Function Documentation